Нужна помощь ESP-12E

[maxs2389081]

Шью через ArduinoIDE
Esp была подключена правильно, через usb-ttl , отдельное питание, gpio0 при прошивке на землю, перезапускаю замыкание reset на землю перед каждой прошивкой.
Раньше всё работало.
Пишет:
esptool v0.4.13 - (c) 2014 Ch. Klippel <ck@atelier-klippel.de>
setting board to nodemcu
setting baudrate from 115200 to 115200
setting port from COM1 to COM8
setting address from 0x00000000 to 0x00000000
espcomm_upload_file
espcomm_upload_mem
setting serial port timeouts to 1000 ms
opening bootloader
resetting board
trying to connect
flush start
setting serial port timeouts to 1 ms
setting serial port timeouts to 1000 ms
flush complete
espcomm_send_command: sending command header
espcomm_send_command: sending command payload
espcomm_send_command: receiving 36 bytes of data
warning: espcomm_send_command: wrong direction/command: 0x00 0x08, expected 0x01 0x08
trying to connect
flush start
setting serial port timeouts to 1 ms
setting serial port timeouts to 1000 ms
flush complete
espcomm_send_command: sending command header
espcomm_send_command: sending command payload
espcomm_send_command: receiving 36 bytes of data
warning: espcomm_send_command: wrong direction/command: 0x00 0x08, expected 0x01 0x08
trying to connect
flush start
setting serial port timeouts to 1 ms
setting serial port timeouts to 1000 ms
flush complete
espcomm_send_command: sending command header
espcomm_send_command: sending command payload
espcomm_send_command: receiving 36 bytes of data
warning: espcomm_send_command: wrong direction/command: 0x00 0x08, expected 0x01 0x08
Произошла ошибка при загрузке скетча
resetting board
trying to connect
flush start
setting serial port timeouts to 1 ms
setting serial port timeouts to 1000 ms
flush complete
espcomm_send_command: sending command header
espcomm_send_command: sending command payload
espcomm_send_command: receiving 36 bytes of data
warning: espcomm_send_command: wrong direction/command: 0x00 0x08, expected 0x01 0x08
trying to connect
flush start
setting serial port timeouts to 1 ms
setting serial port timeouts to 1000 ms
flush complete
espcomm_send_command: sending command header
espcomm_send_command: sending command payload
espcomm_send_command: receiving 36 bytes of data
warning: espcomm_send_command: wrong direction/command: 0x00 0x08, expected 0x01 0x08
trying to connect
flush start
setting serial port timeouts to 1 ms
setting serial port timeouts to 1000 ms
flush complete
espcomm_send_command: sending command header
espcomm_send_command: sending command payload
espcomm_send_command: receiving 36 bytes of data
warning: espcomm_send_command: wrong direction/command: 0x00 0x08, expected 0x01 0x08
resetting board
trying to connect
flush start
setting serial port timeouts to 1 ms
setting serial port timeouts to 1000 ms
flush complete
espcomm_send_command: sending command header
espcomm_send_command: sending command payload
espcomm_send_command: receiving 36 bytes of data
warning: espcomm_send_command: wrong direction/command: 0x00 0x08, expected 0x01 0x08
trying to connect
flush start
setting serial port timeouts to 1 ms
setting serial port timeouts to 1000 ms
flush complete
espcomm_send_command: sending command header
espcomm_send_command: sending command payload
espcomm_send_command: receiving 36 bytes of data
warning: espcomm_send_command: wrong direction/command: 0x00 0x08, expected 0x01 0x08
trying to connect
flush start
setting serial port timeouts to 1 ms
setting serial port timeouts to 1000 ms
flush complete
espcomm_send_command: sending command header
espcomm_send_command: sending command payload
espcomm_send_command: receiving 36 bytes of data
warning: espcomm_send_command: wrong direction/command: 0x00 0x08, expected 0x01 0x08
warning: espcomm_sync failed
error: espcomm_open failed
error: espcomm_upload_mem failed

 

[nikolz]

Шью через ArduinoIDE
Esp была подключена правильно, через usb-ttl , отдельное питание, gpio0 при прошивке на землю, перезапускаю замыкание reset на землю перед каждой прошивкой.
Раньше всё работало.
Пишет:
esptool v0.4.13 - (c) 2014 Ch. Klippel <ck@atelier-klippel.de>
setting board to nodemcu
setting baud
error: espcomm_upload_mem failed

кто-то уже прибегал с подобным.
судя по сообщению предположу, что у вас ошибка в программе (возможно надо что-то обновить)