столкнулся с проблемой с прошивкой bruce

[ramseqz]

E (661) esp_ota_ops: not found otadata
{
"DC:B49:136C": {
"rot": 1,
"irTx": 40,
"irTxRepeats": 0,
"irRx": 46,
"rfTx": 8,
"rfRx": 46,
"rfModule": 0,
"rfFreq": 433.92,
"rfFxdFreq": 1,
"rfScanRange": 3,
"bleName": "Keyboard_d6",
"rfidModule": 0,
"gpsBaudrate": 9600,
"iButton": 0,
"CC1101_Pins": {
"sck": 12,
"miso": 13,
"mosi": 11,
"cs": 10,
"io0": 9,
"io2": -1
},
"NRF24_Pins": {
"sck": -1,
"miso": -1,
"mosi": -1,
"cs": -1,
"io0": -1,
"io2": -1
},
"SDCard_Pins": {
"sck": -1,
"miso": -1,
"mosi": -1,
"cs": -1,
"io0": -1,
"io2": -1
},
"W5500_Pins": {
"sck": -1,
"miso": -1,
"mosi": -1,
"cs": -1,
"io0": -1,
"io2": -1
},
"LoRa_Pins": {
"sck": -1,
"miso": -1,
"mosi": -1,
"cs": -1,
"io0": -1,
"io2": -1
},
"i2c_bus": {
"sda": 8,
"scl": 46
},
"uart_bus": {
"rx": 46,
"tx": 8
},
"GPS_bus": {
"rx": 46,
"tx": 8
}
}
}MESSAGE: Scanning Networks..
IP: 172.0.0.1
Configuring Webserver ...
Webserver started

��█████ ██████ ██ ██ ██████ ███████
██ ██ ██ ██ ██ ██ ██ ██
██████ ██████ ██ ██ ██ █████
██ ██ ██ ██ ██ ██ ██ ██
██████ ██ ██ ████���█ ██████ ███████

PREDATORY FIRMWARE

Tips: Connect to the WebUI for better experience
Add your network by sending: wifi add ssid password

At your command:
может кто то подсказать в чем проблема?. у меня esp 32 s3 n16r8

 

[ramseqz]

E (661) esp_ota_ops: not found otadata
{
"DC:B49:136C": {
"rot": 1,
"irTx": 40,
"irTxRepeats": 0,
"irRx": 46,
"rfTx": 8,
"rfRx": 46,
"rfModule": 0,
"rfFreq": 433.92,
"rfFxdFreq": 1,
"rfScanRange": 3,
"bleName": "Keyboard_d6",
"rfidModule": 0,
"gpsBaudrate": 9600,
"iButton": 0,
"CC1101_Pins": {
"sck": 12,
"miso": 13,
"mosi": 11,
"cs": 10,
"io0": 9,
"io2": -1
},
"NRF24_Pins": {
"sck": -1,
"miso": -1,
"mosi": -1,
"cs": -1,
"io0": -1,
"io2": -1
},
"SDCard_Pins": {
"sck": -1,
"miso": -1,
"mosi": -1,
"cs": -1,
"io0": -1,
"io2": -1
},
"W5500_Pins": {
"sck": -1,
"miso": -1,
"mosi": -1,
"cs": -1,
"io0": -1,
"io2": -1
},
"LoRa_Pins": {
"sck": -1,
"miso": -1,
"mosi": -1,
"cs": -1,
"io0": -1,
"io2": -1
},
"i2c_bus": {
"sda": 8,
"scl": 46
},
"uart_bus": {
"rx": 46,
"tx": 8
},
"GPS_bus": {
"rx": 46,
"tx": 8
}
}
}MESSAGE: Scanning Networks..
IP: 172.0.0.1
Configuring Webserver ...
Webserver started

��█████ ██████ ██ ██ ██████ ███████
██ ██ ██ ██ ██ ██ ██ ██
██████ ██████ ██ ██ ██ █████
██ ██ ██ ██ ██ ██ ██ ██
██████ ██ ██ ████���█ ██████ ███████

PREDATORY FIRMWARE

Tips: Connect to the WebUI for better experience
Add your network by sending: wifi add ssid password

At your command:
может кто то подсказать в чем проблема?. у меня esp 32 s3 n16r8

запускается только от пинка от пк. пока не зайду в консоль через esptool.js сайт